"Cream to Clean" Cleansing Foam

This cleansing foam gently rids your face of dirt and makeup and is suitable for all skin types.

The combination of the extremely mild surfactants Sodium Lauroyl Glutamate and Lauryl Glucoside creates a very creamy, fine-pored foam. The high proportion of the humectants propanediol, glycerin, and jojoba ester gel effectively preserves skin moisture and makes the product even milder. Calcium Pantothenate has a moisturizing, soothing, and irritation-reducing effect.

Difficulty level: ⭐easy

Preparation time: ⏱ approx. 20 minutes

Ingredients in percent

A1 53.2 dist. water
1.3 citric acid
0.5 Calcium Pantothenate
2 Preblend Aqua
A2 25 Sodium Cocoyl Glutamate (30%)
B 6 Lauryl Glucoside
C 5 Propanediol Green
5 glycerin
2 jojoba ester gel

YIELDS 100%

Instructions

  1. Weigh all ingredients from A1 and stir until all substances have dissolved clearly in the water.
  2. Now add A2. The mixture will become cloudy due to gas formation. Wait briefly if necessary until the air has escaped.
  3. Weigh B (Lauryl Glucoside) into a heat-resistant container and heat it slightly until it is liquid and clear (approx. 30-40 degrees is sufficient). Alternatively, you can heat the container in a water bath beforehand, so you can work with the liquid product immediately.
  4. Now add B to A1/A2 and stir in well.
  5. Then weigh phase C and stir C together until the jojoba ester has dissolved clearly.
  6. Now add C thoroughly to A/B.
  7. Adjust the pH value to approx. 5.3 – 5.5.
  8. Fill your product into a foamer bottle. The surface foam will dissolve overnight. A crystal-clear solution will remain.

Tip:

Fill the product into a foamer bottle . The surface foam will dissolve overnight, leaving a crystal-clear solution. You can find out why distilled water is important here.


FAQ: Frequently Asked Questions about "Cream to Clean" Cleansing Foam

Für welche Hauttypen eignet sich der Reinigungsschaum „Cream to Clean“?

Der milde Reinigungsschaum befreit das Gesicht sanft von Schmutz und Make-up und eignet sich für alle Hauttypen.

Wie aufwendig ist die Herstellung?

Das Rezept ist leicht und in etwa 20 Minuten fertig. Nur das Lauryl Glucoside wird leicht auf 30 bis 40 Grad erwärmt, bis es flüssig und klar ist.

Warum ist der Reinigungsschaum so mild?

Die sehr milden Tenside Sodium Cocoyl Glutamate und Lauryl Glucoside erzeugen einen cremigen, feinporigen Schaum. Propandiol, Glycerin und Jojobaester-Gel bewahren die Hautfeuchtigkeit, Calcium Pantothenate wirkt beruhigend und irritationsmildernd.

Warum wird die Mischung beim Herstellen trüb?

Beim Zufügen von Phase A2 entsteht durch die Reaktion mit der Zitronensäure Gas, wodurch die Masse kurz trüb wird. Warte einfach, bis die Luft entwichen ist. Der Oberflächenschaum löst sich über Nacht auf und es bleibt eine klare Lösung.

Welchen pH-Wert hat der Reinigungsschaum und wie fülle ich ihn ab?

Der pH-Wert wird auf etwa 5,3 bis 5,5 eingestellt. Abgefüllt wird das Produkt in einen Foamer, der beim Pumpen den Schaum erzeugt.